I have decided to sell everything as a turn key operation for someone looking to get into racing and needs everything. The car ran Watkins Glen Fun One last fall and was one of the top cars in the field. The car was prepped for Lime rock for this year but that never happened. So in light of the current situation I am offering everything as a complete package for sale. It includes a well sorted Mygale F2000 car, all the spares, all the information pertaining to the setup for the car, plus trailer for $32,000. The car is ready to race right now. The setup is good for many of the North East tracks, Lime Rock, Palmer, Thompson, New Hampshire. 2003 MYGALE F2000 car. Imported by PR1 Motorsports and raced on the west coast . I have raced it on the east coast for the past few years. $35,000 takes everything.
HISTORY
2014 car was taken down to bear frame , paint removed, put on flat plate , checked for cracks and repainted with Imron. New aluminum belly pan was installed. All the body work paint was removed, and body panels were repaired and repainted. Over 20 pounds of old paint were removed.
2016 car was taken down to the frame and all wishbones were inspected and adjusted. All rod ends were inspected and replaced as needed. Uprights and bearings were inspected and serviced , along with brakes and tripod joints.
1/2014 new Alcon brake calipers and brake pads
1/2014 new brake discs by Colman Brothers Racing , new bobbins and bolts.
2/2014 new steering rack , redesigned and better material and technology
2/2014 new AIM EVO4 data system installed with steering, brakes, and shock data . Car has a PECTEL ECU
2/2015 new fire system, new bottle and nozzles, Electric
4/2015 new Penske shocks, rebuilt 2/2016, new valving
5/2015 Quicksilver Zetec was rebuilt. To date 7 race weekends and 7 practice days +-
5/2015 new clutch, pressure plate, slave cylinder, and throw out bearing
8/2015 new stub axles front and rear by Two Dogg
8/2015 new fuel pump
9/2015 rebuilt LD 200 transmission with over $9500.00 in new parts and labor.
5/2017 new Tilton brake master cylinders
custom nose
Radon front wing assembly
custom side pod floors so any defuser on the market can be used on this car
pennon defuser
custom engine cover and side panels
rear lower wing, Pennon
rear upper wing VD
also has a high down force rear upper wing VD
3 full sets of OZ mag. wheels made for these cars only by OZ when the car was raced in the European series . No longer available
I also have 2 of these OZ wheels for the front and 1 rear wheel.
belts run out this year and need to be replaced
Car will be sold with one set of gears and one set of springs of your choice.
SPARES
I have a complete main body purchased from PR1 Motorsports new.
camber shims of all sizes
1 new starter
1 new solenoid
1 new set of injectors
1 new steering link
2 new wheel bearing assemblies with new seals
2 new upright steering link fittings
1 new left side, side pod floor.
USED PARTS
1 10 mm antiroll bar
1 14 mm antiroll bar
assorted antiroll bar blades and fittings
1 steering link
1 upright
1 rear stub axle Mygale
2 front stub axles Mygale
Tripod joints and housings
complete set of castings and fittings for rear suspension of car
wheel nut parts
assorted bell crank parts front and rear
assorted special nuts, washers, bolts, fittings for Mygale
1 Zetec, Mygale header
1 radiator
2 oil coolers
2 clutch slave cylinders with throw out bearings
clutch install tool
extra water pipes
Zetec coil and harness
repairable LD 200 rear cover
upper side pod body mounts
Radon wing end plates
wing skid plates
assorted broken wishbones, steering links, push rods
Any bolt that could be changed from metric to an AN bolt or nut has been changed
Any threaded hole that was metric has been left metric.
SaveSave