Amazing!
When did you start fabricating parts. This project has moved on with incredible speed. 6-8 months?
Magnificent Jon.
Thanks ... Jay Novak
I don't know about FF, but I had a 2001 Red Devil F500 that had a one-piece body, except for the very front of the nose section.
Yes, it was a PITA....until I figured out the "easy way" to pull it off or put it on. Loosen all the dzus fittings, then stand in the cockpit, lift the body up, then step out of the cockpit and set the body back down onto the ground. Reverse to put the body on. This might not be so easy with a body that is either too heavy or not well balanced front-to-rear.....
Once I got it figured out, it was actually pretty fast and easy to deal with.....though I took the brunt of a few paddock jokes when people saw the process.
On-topic, that's a heck of a nice job you did with that car! Can't wait to see it at speed.
Marshall Mauney
Milwaukee Region
Here's my newest trailer. It's made of Birch plywood from Russia, Okoume plywood from France, and Yellow Pine and Douglas Fir from Saginaw, MI. The Pine & Fir were originally bleechers removed from 2 high schools in Saginaw. This is the best wood of its type that I've seen since the 70's.
The first photo shows the sophisticated tools required for such a project. The plywood sheets were scarffed (beveled joint) together. There are, essentially, no structural fasteners in the entire trailer. It relies, instead, on epoxy glue. The storage unit on the left side contributes to tortional strength.
The outside of the trailer is coated with WEST System epoxy, followed by several coats of clear automotive enamel.
There's a bed across the front of the trailer that swings up for access to 2 complete sets of tires. Hal Pringle's idea. The axle is a 3500# tortion axle, allowing the floor of the trailer to be 9" above the road. There's a hand-operated winch on the back left side that, through a pulley system, will draw the car into the trailer. Should make the car easy to load. All tools are stored on the inside of the entry door. The tubes for the canopy are stored inside the 3 plastic pipes below the storage unit. Total weight is 1200#.
Look's great Jon, any pic's of the car with paint? Are the hole's on top vent's or sky lite's? I cant remember a round combo..
shouldn't this be in Architectural Digest or something?
love the aero-engine dangling from the rafters
your stuff is awesome
Very nice looking trailer Jon.
I'm exhausted building a car, let alone a trailer as well!
Desmond
Pretty slick Jon. Did you get the mini van tow vehicle yet?
Clark
I haven't painted the car yet because it's time to concentrate on my DSR Also the steering rack has been back ordered since December. I think by mid season I'll have time to finish and test the FB.
The holes in the trailer are skylights
I have a new tow vehicle Clark mentioned that I will start modifying tomorrow.
Thanks for the comments.
Jon
Cant wait to see what you have up your sleeve for a tow vehicle.
Will it be a woodie?
Marty
That is awesome looking work, Jon. I would've never thought wood to be a good medium choice for as much as you do with it. I couldn't even make a pretty Pine Wood Derby car in school.
Side question- is that a Lycoming TIGO-480 engine hanging from the ceiling next to the SR body in the 6th picture?
~Matt Clark | RTJ-02 FV #92 | My YouTube Onboard Videos (helmet cam)
Matt,
The engine is a GO435 a smaller version of the 480.
However in the mid 90's I did design, build, and fly in aerobatic competition the plane in the attached photo. Sorry about the photo but I took it today of a picture hanging on the wall in my shop.
That plane did have a geared supercharged 480 in it.
340HP
54GPH
29 Gal fuel tank
93" Dia. Prop
Sea level power to 8000'
1300LB.
I flew it to Texas from Michigan twice for the US Nationals.
I was essentially breaking the FAA required fuel reserved minimums upon departure.
Lots of fuel stops, no GPS or Nav.
That said, I bought the 435 because I miss the plane and want to build an old mans version.
The geared engines sound cool too. But only from the outside.
Not a lot of people would recognize that engine.
Jon
Ah, ok. Its tough to pick out the details from that little bit I could see. Just caught my eye + interest because I'm a Designer at Lycoming. We don't see much (ok...any) of the older models needing Engineering work anymore.
~Matt Clark | RTJ-02 FV #92 | My YouTube Onboard Videos (helmet cam)
Just awesome stuff. Seriously cool, fantastic work. Wish I lived near you and could come help/ learn!
Sean O'Connell
1996 RF96 FC
1996 RF96 FB
2004 Mygale SJ04 Zetec
Did I read right 54 gph and 29 gal fuel tank.
That would equal about half an hour flying time on a tank.
I can see why lots of fuel stops.
Did the FB car ever get completed or raced?
Marty
Very neat car. Did it take to the track?
Chris
I can't comment on how often it has been out, but I have seen Jon out at Waterford for a test day in the car. My guess would he that we'll see this car at least a few times over the summer.
Jon,
beautiful work! You could make a good sideline restoring Mosquitos! I'll ask the question nobody has, but might be thinking: How much would it cost to have you make a trailer like yours for one of us? I'm going to use your ideas as a guide to make a liftable cover for my open trailer, but I know the work will be nothing like you are capable of. I agonized over buying your former trailer with the lift up side door and swing out hoist, but it was too far away to justify at the time.
Thanks, Brad
There are currently 2 users browsing this thread. (0 members and 2 guests)