Results 1 to 6 of 6
  1. #1
    Member
    Join Date
    07.30.24
    Location
    Torrance, California
    Posts
    5
    Liked: 0

    Default Reynard Floor Panel - To bond or not to bond.

    Hi,

    The chassis for my '84 Reynard FF is shortly off for powder coating back to semi-gloss black as it would have been from the factory. Surprisingly, the chassis is quite straight and with very little evidence of previous damage. There is light surface rust, but nothing too bad - probably a legacy of coming from Arizona!

    I know the topic of bonding the floor panel has been well covered on here but my question is 'should I bond it on'? It wasn't bonded from the factory, this was a good car in it's day and I wonder if bonding the floor on will change the characteristics of the car. I recognize that it could probably 'improve' the car, but is that really the idea?

    I'd be interested to hear from anyone who has one of these cars on their experience and if they bonded or not, the pro's and con's generically to bonding etc.

    Thank you.

    Max

  2. #2
    Contributing Member Lotus7's Avatar
    Join Date
    08.10.05
    Location
    Savannah, GA
    Posts
    2,369
    Liked: 887

    Default

    If the car has not yet gone to powder coat, definitely hold off until you make the "bond or not" decision. You want the glue on freshly cleaned, dried bare steel.

    I know nothing of rocker arm cars, as to whether they like a flexy chassis or not, hopefully others chime in.
    Ian Macpherson
    Savannah, GA
    Race prep, support, and engineering.

  3. #3
    Contributing Member Rick Kirchner's Avatar
    Join Date
    02.24.02
    Location
    Tehachapi, CA
    Posts
    6,646
    Liked: 1616

    Default

    A good powder coat shop will mask the areas that need masking with a heat resistant tape and silicone plugs for all the fastener holes.

    You can buy both on Amazon, do the work yourself, and have it done right and cheaper too.

    I can't stress this enough, you want to mask all the fastener holes or buy a reamer for each size bolt (not a drill bit!).

    Not sure I'd coat after bonding. The oven is hot enough to break down the glue to some extent.

    9/10 the lack of factory bonding was due to cost and not performance.

  4. The following members LIKED this post:


  5. #4
    Contributing Member Lotus7's Avatar
    Join Date
    08.10.05
    Location
    Savannah, GA
    Posts
    2,369
    Liked: 887

    Default

    Quote Originally Posted by Rick Kirchner View Post
    A good powder coat shop will mask the areas that need masking with a heat resistant tape and silicone plugs for all the fastener holes.

    .
    Agreed, my comment was meant to prevent the possible case of "send a masked chassis to coating, get it back, then decide not to bond the floor".
    Now the chassis is bare on the bottom after coating...
    cheers
    Ian Macpherson
    Savannah, GA
    Race prep, support, and engineering.

  6. The following members LIKED this post:


  7. #5
    Contributing Member DanW's Avatar
    Join Date
    03.22.03
    Location
    Benicia, Calif
    Posts
    3,166
    Liked: 985

    Default Bond it

    As someone who has peeled about 18" of the pan away from an off at Buttonwillow, I vote for bonding. There is nothing like realizing as you come into the paddock that the floor of your car is scraping on the ground and your fuel cell has pieces of asphalt packed underneath it...

    His Purpleness had it even worse with his FC.
    “Racing makes heroin addiction look like a vague wish for something salty.” -Peter Egan

  8. The following 3 users liked this post:


  9. #6
    Senior Member Nardi's Avatar
    Join Date
    08.16.09
    Location
    Southeast
    Posts
    890
    Liked: 125

    Default

    I used to race an 84 Reynard FC. They are very good and forgiving cars. But I would definitely bond the floor and use the proper rivets (as has been discussed in another thread).
    I had a constant issue with loose rivets and pan due to a lack of bonding. Maybe that’s what makes the car so good, but the constant maintenance was a bit of a chore.

Thread Information

Users Browsing this Thread

There are currently 3 users browsing this thread. (1 members and 2 guests)

  1. pooch776

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  




About Us
Since 2000, ApexSpeed.com has been the go-to place for amateur road racing enthusiasts, bringing together a friendly community of racers, fans, and industry professionals. We're all about creating a space where people can connect, share knowledge, and exchange parts and vehicles, with a focus on specific race cars, classes, series, and events. Our community includes all major purpose-built road racing classes, like the Sports Car Club of America (SCCA) and various pro series across North America and beyond. At ApexSpeed, we're passionate about amateur motorsports and are dedicated to helping our community have fun and grow while creating lasting memories on and off the track.
Social