Results 1 to 10 of 10
  1. 01.14.23, 2:08 PM #1
    B17overhead
    B17overhead is offline
    Senior Member
    Join Date
    08.27.05
    Location
    Prescott, AZ
    Posts
    323
    Liked: 21

    Default Parting out small formula car

    Parts left now with reduced pricing as well:

    Complete carbureted Honda CBR600 F3 600cc with 4-into-1 header that looks to have been modified for formula car chassis. 100+ HP at 12,000 RPM with 4 carbs. Estimate 75-85 HP with FSAE restrictor and a single carb. Could be increased to 700 cc and probably over 90 HP now with latest FSAE rules. (All figures are for 100 unleaded, but probably no different for E85) Factory carbs and factory airbox with new air cleaner. Vance and Hines ignition electronics, complete harness and Autometer Tach. Includes chassis mounts/braces/rear chassis bulkhead for motor which allow it to sit upright on a flat surface.
    Was $400, now $250.
    Note $250 is about 50% of typical Ebay cost for this particular motor.
    I'm not up for crating and shipping- now has to be a pickup or nearby by delivery by me.
    Attached Images Attached Images
    Last edited by B17overhead; 01.31.23 at 9:50 PM.
    Reply With Quote Reply With Quote
  2. 01.14.23, 3:51 PM #2
    Lastminuteracin
    Lastminuteracin is online now
    Senior Member
    Join Date
    05.15.22
    Location
    Sacramento, California
    Posts
    189
    Liked: 100

    Default

    Message sent.
    Reply With Quote Reply With Quote
  3. 01.15.23, 8:04 PM #3
    128racecar
    128racecar is offline
    Junior Member
    Join Date
    03.20.14
    Location
    Indianapolis
    Posts
    2
    Liked: 0

    Default

    PM sent
    Reply With Quote Reply With Quote
  4. 01.31.23, 8:27 AM #4
    kingmotorsport
    kingmotorsport is offline
    Junior Member
    Join Date
    07.21.09
    Location
    Haddonfield, NJ
    Posts
    2
    Liked: 0

    Default

    Are you willing to ship front end?




    Quote Originally Posted by B17overhead View Post
    Parts left now:

    Complete Honda 600cc. Factory carbs and airbox. Vance and Hines electronics, complete harness $400


    New never used: Autometer gauges, 2604 2" mech oil pressure with tubing in original box with mounting hardware $10, 2635 2" temperature gauge - will need sender- in original box with mounting hardware $10

    4 Keizer magnesium centers with 7 and 8 inch spun aluminum wheel halves. $275 each or 850 for all 4.
    Alpha steering wheel. Like new

    Both front corners
    That would be a-arms, uprights with brakes, stub axles, and wheel hubs. $15 for all.
    Reply With Quote Reply With Quote
  5. 01.31.23, 11:11 AM #5
    Earley Motorsports
    Earley Motorsports is offline
    Contributing Member Earley Motorsports's Avatar
    Join Date
    11.03.10
    Location
    Murfreesboro, TN
    Posts
    1,476
    Liked: 436

    Default Gauges

    If you still have the gauges I'll take them. PM sent
    Graham
    Reply With Quote Reply With Quote
  6. 01.31.23, 1:11 PM #6
    B17overhead
    B17overhead is offline
    Senior Member
    Join Date
    08.27.05
    Location
    Prescott, AZ
    Posts
    323
    Liked: 21

    Default

    .
    Last edited by B17overhead; 01.31.23 at 4:23 PM.
    Reply With Quote Reply With Quote

  7. The following members LIKED this post:

    Earley Motorsports
  8. 02.15.24, 10:16 AM #7
    10rmotor
    10rmotor is online now
    Contributing Member
    Join Date
    10.08.06
    Location
    San Jose, Ca
    Posts
    804
    Liked: 114

    Default

    Hey chuck if you still have the tach and its a pro cycle tach (14k?) I'm interested.
    Reply With Quote Reply With Quote
  9. 02.15.24, 2:49 PM #8
    B17overhead
    B17overhead is offline
    Senior Member
    Join Date
    08.27.05
    Location
    Prescott, AZ
    Posts
    323
    Liked: 21

    Default

    Quote Originally Posted by 10rmotor View Post
    Hey chuck if you still have the tach and its a pro cycle tach (14k?) I'm interested.
    Think it went with the MC motor. I took one quick look just now and didn't see it. Look again later today.
    Reply With Quote Reply With Quote

  10. The following members LIKED this post:

    10rmotor
  11. 02.15.24, 4:27 PM #9
    Onebadbug
    Onebadbug is offline
    Member
    Join Date
    11.02.16
    Location
    Spokane, Washington
    Posts
    63
    Liked: 17

    Default

    Bolt pattern on the wheels?
    Reply With Quote Reply With Quote
  12. 02.15.24, 5:43 PM #10
    B17overhead
    B17overhead is offline
    Senior Member
    Join Date
    08.27.05
    Location
    Prescott, AZ
    Posts
    323
    Liked: 21

    Default

    Quote Originally Posted by Onebadbug View Post
    Bolt pattern on the wheels?
    Wheels are long gone. Sorry.
    They were all 4x100mm Keizer lead anchor heavy alum centers and new Magnesium centers
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules





About Us
Since 2000, ApexSpeed.com has been the go-to place for amateur road racing enthusiasts, bringing together a friendly community of racers, fans, and industry professionals. We're all about creating a space where people can connect, share knowledge, and exchange parts and vehicles, with a focus on specific race cars, classes, series, and events. Our community includes all major purpose-built road racing classes, like the Sports Car Club of America (SCCA) and various pro series across North America and beyond. At ApexSpeed, we're passionate about amateur motorsports and are dedicated to helping our community have fun and grow while creating lasting memories on and off the track.
Site Info
Terms and Conditions
Forum Rules
Privacy Policy
Current Advertisers
Advertising Information
Reset Lost Password
Social