Activity Stream

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums Articles Articles

07.11.25, 12:44 PM

marck_c replied to a thread PFM rear rocker anatomy in PFM: Pro Formula Mazda

also interested in this

1 replies | 1027 view(s)

07.11.25, 12:19 PM

CGOffroad replied to a thread Minor Rant in SCCA Board of Directors Q&A

Reading the condition above, my first thought is that the shoulder belts were not installed with correct angularity with regard to drivers shoulders....

18 replies | 17559 view(s)

07.11.25, 11:13 AM

Peter Olivola replied to a thread Minor Rant in SCCA Board of Directors Q&A

UV doesn't increase belt stretch. Just the opposite. It embrittles the fabric.

18 replies | 17559 view(s)

07.11.25, 10:36 AM

grapefarmeral replied to a thread Minor Rant in SCCA Board of Directors Q&A

When I was skydiving, I was always told to keep my rig out of the sun (UV) It seemed to make sense. After i started racing I saw, if I remember...

18 replies | 17559 view(s)

07.11.25, 9:39 AM

Rick Kirchner replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

Might look around Tucson. Short drive from Phx, large concentration of military contractors.

11 replies | 520 view(s)

07.11.25, 8:59 AM

billtebbutt replied to a thread Trailer bearing question in Trailering & Towing

Probably, but it was empty on the way back so unlikely in this case. best bt

5 replies | 249 view(s)

07.11.25, 6:00 AM

pacratt replied to a thread Trailer bearing question in Trailering & Towing

Unless I'm over-thinking, side-to-side weight distribution of cargo could also play a role...yes?...no? Glenn

5 replies | 249 view(s)

07.11.25, 12:13 AM

sabre1fv started a thread Stuska Engine Dyno with Dyno Datamite Analyzer in

Open Motorsports Classifieds

Stuska XS-19 High Performance Engine dyno (good for up to 175 HP) paired with a Datamite data logger for sale $2500 plus shipping (pick-up...

0 replies | 124 view(s)

07.11.25, 12:10 AM

SteveG replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

I just found a new place today for mil-spec stuff. I was looking for a specific MS21250 bolt and appropriate washers and found them in stock at...

11 replies | 520 view(s)

07.10.25, 11:52 PM

Skelly started a thread Vara race at the new buttonwillow circut RENTAL in Vintage: Events, Clubs & Organizations

We will be bringing 2 cars for the VARA event at Buttonwillows new track September 13-14. Our 75 TIGA will be available for rent for the event. if...

0 replies | 64 view(s)

07.10.25, 9:06 PM

Offcamber1 replied to a thread two (2) 1600 Kent Ford (ie: FFord) intake manifolds in

FF: Classifieds: Wanted

Art, check your PMs. If you don't have one from me, PM me back and I will try again. Kip

1 replies | 252 view(s)

07.10.25, 8:57 PM

Purple Frog replied to a thread Minor Rant in SCCA Board of Directors Q&A

...

18 replies | 17559 view(s)

07.10.25, 7:59 PM

DanW replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

Commercial grade fasteners are no longer made in the US, mostly Korea (KS) on the bolt head, China and India. There is no QC for any of it, just...

11 replies | 520 view(s)

07.10.25, 6:37 PM

Rick Iverson replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

Carroll Smith: “They don’t put Grade 8 bolts on airplanes, why would you put them on a race car.”

11 replies | 520 view(s)

07.10.25, 6:05 PM

R. Pare replied to a thread Slow Apex Server Speed in General Formula Car Discussion

It is working fast for me at the moment.

14 replies | 529 view(s)

07.10.25, 6:00 PM

andyllc replied to a thread Minor Rant in SCCA Board of Directors Q&A

Every time I see this thread I think we are complaining about something Tim Minor did! ha!

18 replies | 17559 view(s)

07.10.25, 5:18 PM

Steve Demeter replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

Carroll Smith said to avoid Grade 8 like the plague Brittle and QC is poor compared to AN.

11 replies | 520 view(s)

07.10.25, 5:16 PM

Steve Demeter replied to a thread Slow Apex Server Speed in General Formula Car Discussion

slow right now. Damn hackers or whatever they are....

14 replies | 529 view(s)

07.10.25, 5:14 PM

BLS replied to a thread Race car hardware , Phoenix, AZ in General Formula Car Discussion

Grade 8 at lowes/hd will likely be available only as coarse thread, and made in china. I would not trust the G8 stuff at all. Figure out what you...

11 replies | 520 view(s)

07.10.25, 3:26 PM

billtebbutt replied to a thread Trailer bearing question in Trailering & Towing

This is brilliant! you are correct - the side where the warmer bearings were, was in the smoking hot sun the entire drive on teh last day back. I...

5 replies | 249 view(s)

07.10.25, 3:21 PM

Dennis McCarthy replied to a thread Minor Rant in SCCA Board of Directors Q&A

There is an old saying that a wise man told me: "it's never a problem until it's a problem and then the finger pointing begins"....

18 replies | 17559 view(s)

07.10.25, 3:12 PM

Charles Warner replied to a thread Ralt RT5 5 parts in

Vintage: Classifieds: Wanted

What parts do you require? What configuration? Narrow Track, Wide Track?

1 replies | 102 view(s)

07.10.25, 2:51 PM

10rmotor replied to a thread Trailer bearing question in Trailering & Towing

If you're really concerned, which it doesn't sound like you are, you can always do the torque and back off one flat per mfg. instructions. Is it...

5 replies | 249 view(s)

07.10.25, 2:47 PM

jtaphorn replied to a thread Trailer bearing question in Trailering & Towing

Potential solar heating since both axles on side affected. Which side of the trailer was facing the sun.

5 replies | 249 view(s)

07.10.25, 2:05 PM

sandraalan started a thread Ralt RT5 5 parts in

Vintage: Classifieds: Wanted

I am looking for suspension parts for a 1982 Ralt RT5 5 Super Vee. Does anyone have them or know who builds them? Thanks

1 replies | 102 view(s)

07.10.25, 1:39 PM

emackey replied to a thread MN Summer Majors - BIR in FF: Event News, Info & Results

Good luck to everyone racing in the Cat Majors at Road America this weekend! We're up to 5 FF's entered so far in the MN Summer Majors at...

3 replies | 4494 view(s)

07.10.25, 11:46 AM

billtebbutt started a thread Trailer bearing question in Trailering & Towing

Good morning folks, Just did a 4,000km round trip with our old 30' Haulmark. Because I am paranoid, I check the hubs every time I fuel up,...

5 replies | 249 view(s)

07.10.25, 9:12 AM

Eric Cruz replied to a thread FE2 w/ FRP At Summit Poin in FE: Event News, Info & Results

I want to second Gabe's assessment of running with FRP. I registered two cars this morning and came here to post about what great events FRP runs -...

1 replies | 792 view(s)

07.10.25, 7:34 AM

Ed Womer replied to a thread Seeking Mysterian (M2) setup advice in FV: General Discussion

This would be MY opinion, but I see a few things I would change, based on experience of the 40 years of doing this. First, the large aluminum rockers...

7 replies | 426 view(s)

07.10.25, 7:31 AM

Robins Ken replied to a thread Ex Patrick Racing Lola T94/00 Build Thread in BOSS Formula Cars

Good looking car. Makes a current Indy car look like a hippo. Met Willy in Feb. 1990 at Denny's Big Spring Texas. A few Indy and Indy Lights...

75 replies | 81386 view(s)

About Us

Site Info

Social