WTB: 8" and 10" Wheels

[openwheeler37]

I'm looking for some 8" and 10" wheels for spares. E-mail me @ ggreenfield@bergstromauto.com

[Purple Frog]

Might want to mention what hub they need to fit on.

[GAR]

I have a set for F2000 cars if that works for you

[openwheeler37]

Might want to mention what hub they need to fit on.

To be honest, I dont know the size. Its for a Speads F1000 if that helps. I'm new to the series and to these cars so im not sure what hub size it is (didnt know there different sizes for these cars)

[Purple Frog]

Did you call Bob yet? He knows everything about Speads.

Bob Schader

1129 Chestnut Ave
Longmont, CO 80503

E-Mail: rkschader@gmail.com
Phone: (303) 516-9217

[F1000champ]

You can also check with Richard Cottrill at Rilltech-Speads at 303-776-8855

[RobLav]

You can also simply take some measurements.

[openwheeler37]

You can also simply take some measurements.

I'd love to but dont know what to measure. When looking at some wheels in the classifeds they talk about 3 measurements: Center, Drive Pin Diameter, and drive pin circle. Where are these taken? Thanks again for all the help.

Example: These are the wheels i'd like but not sure if they fit.

http://www.apexspeed.com/forums/showthread.php?t=46418

[F1000champ]

Contact Richard Cottrill at Rilltech-Speads 303-776-8855, he should be able to give you the measurments. I think the wheels you're looking at on ApexSpeed have been sold by the post.

[openwheeler37]

The wheels have been relisted by a different seller.

[F1000champ]

I'll contact Richard for you and see if I can get you the dimensions for the 2003 Speads wheels.

[openwheeler37]

Might want to mention what hub they need to fit on.

The center hole is 2.25" so I would assume my hub size is 2.25" .... 17/32" drive pin hole and a 3.5" drive pin circle diameter.

[RobLav]

Van Diemen pattern. Makes it easier. Watch for brake caliper clearance (measure) before you purchase. The relatively cheap aluminum Van Diemen OZ's in 8's and 10's will most likely work.

[Mike Holland]

Isn't the VD drive Pin Circle Diameter 3.75"? He is saying his is 3.50"
I believe the Swift pattern is 3.75 also.

[RobLav]

Mike - you are absolutely correct! I blew right over that part. Nice catch.

[openwheeler37]

Isn't the VD drive Pin Circle Diameter 3.75"? He is saying his is 3.50"
I believe the Swift pattern is 3.75 also.

I could have measured wrong ... is the drive pin circle measured form the center of a drive pin hole to center of the drive pin hole directly a crossed from it?

[Mike Holland]

Yes Center to Center of two pins directly across each other. You can measure outside of one pin to inside of the other pin.

[openwheeler37]

Yes Center to Center of two pins directly across each other. You can measure outside of one pin to inside of the other pin.

Thanks ... I will double check this weekend.

[John Mosteller]

Is anyone running 8" and 10" wheels?

[openwheeler37]

The other FB's running here (Blackhawk Farms raceway) all run 8's and 10's

[Mike Holland]

Coop has a set of 8 & 10 wheels for sale that are for a RFR. They have rains on them.

http://www.apexspeed.com/forums/show...499#post337499

[Mike B]

The other FB's running here (Blackhawk Farms raceway) all run 8's and 10's

Who?

[openwheeler37]

Who?

I know both the Mazzio's (Ruddy and Gino) are.

[openwheeler37]

Coop has a set of 8 & 10 wheels for sale that are for a RFR. They have rains on them.

http://www.apexspeed.com/forums/show...499#post337499

Thanks!

[TimWalsh]

I have one set of brand new never had tires mounted on them.

Tim Walsh