End plate aluminum washer

[bryancohnracing]

Friends,

I am in need of 8 large OD (up to 1 inch), 10-32 ID aluminum washers to fasten end plates to a main wing element and flap. I used to have a stock pile of these left over from my race shop days but slowly used them up and have lost track of the resource I had used to obtain them in the past.

These are not countersunk washer, those I can find easily. These are about 1 inch OD, 10-32 ID flat on one side, beveled on the other to a flat surface for a button head allen screw to seat on.

Any help, direction, links etc will be greatly appreciated.

[stonebridge20]

Like these?
I have 6 countersunk and 2 flat

[Mike B]

Something like this?
http://www.gyrodynamics.net/products...inish-washers/

[bryancohnracing]

Like these?
I have 6 countersunk and 2 flat

Mike, the two with flat surfaces are exactly what I am looking for, I just need 8 total. The other mike posted a link to new countersunk ones that might make more sense as its easy to buy new hardware. I was just trying to avoid doing so as this is a short term improvement on a customer car before it gets upgraded to a full width carbon wing this winter.

[SStadel]

Pretty sure everything I have is counter-sunk as well.

[stonebridge20]

Mike, the two with flat surfaces are exactly what I am looking for, I just need 8 total. The other mike posted a link to new countersunk ones that might make more sense as its easy to buy new hardware. I was just trying to avoid doing so as this is a short term improvement on a customer car before it gets upgraded to a full width carbon wing this winter.

Bryan, the countersunk ones I have are new and the 2 flat ones are slightly used. Let me know if you need any of them.

[Stan Clayton]

We carry two sizes of the countersunk aluminum washers, and 1" cad plated STEEL 10-32 washers that take button head screws.

[jrh3]

Friends,

I am in need of 8 large OD (up to 1 inch), 10-32 ID aluminum washers to fasten end plates to a main wing element and flap. I used to have a stock pile of these left over from my race shop days but slowly used them up and have lost track of the resource I had used to obtain them in the past.

These are not countersunk washer, those I can find easily. These are about 1 inch OD, 10-32 ID flat on one side, beveled on the other to a flat surface for a button head allen screw to seat on.

Any help, direction, links etc will be greatly appreciated.

Check with the kart racers. They use a ton of them and are quite reasonably priced.
comet kart sales. $0.50-1.50

[EricP]

Amazon search: Allstar aluminum backer washer

[kea]

Would these work?
.
http://www.racing-stuff.com/images/airwasher.jpg

[Brandon Dixon]

https://behrents.com/pc_combined_res...ld_nms~+washer)

[stonebridge20]

https://behrents.com/pc_combined_res...ld_nms~+washer)

Those are stockcar washers. That's why they're $.99 a piece. We're talking road racing washers here which are $5.25 each.

[BeerBudgetRacing]

Amazon search: Allstar aluminum backer washer

I've bought those before....
https://proshop.summitracing.com/par...8639/overview/

Just fine. I've countersunk them myself when needed.

The black anodized washers are nice though.

[bryancohnracing]

Those are stockcar washers. That's why they're $.99 a piece. We're talking road racing washers here which are $5.25 each.

I'm working on an American Iron class 2005 Mustang, racing at the upcoming NASA championships at Mid Ohio in a few weeks. I think it qualifies for using stock car washers!

[Lyngengr]

Friends,

I am in need of 8 large OD (up to 1 inch), 10-32 ID aluminum washers to fasten end plates to a main wing element and flap. I used to have a stock pile of these left over from my race shop days but slowly used them up and have lost track of the resource I had used to obtain them in the past.

These are not countersunk washer, those I can find easily. These are about 1 inch OD, 10-32 ID flat on one side, beveled on the other to a flat surface for a button head allen screw to seat on.

Any help, direction, links etc will be greatly appreciated.

Try Brad Baytos at Primus racing, he has what you need, something like: https://www.primusracingparts.com/wa...num_p_433.html

[Rick Iverson]

Mike, your mid-year front uprights are a piece of art, Man. Simple beautiful.

Something like this?
http://www.gyrodynamics.net/products...inish-washers/