https://ellerymotorsport.com/products/fcp825r-ferodo
Type: Posts; User: Raleigh
https://ellerymotorsport.com/products/fcp825r-ferodo
That port is a vent for the cold start circuit. Most blank them off when doing the cold start delete mod due fuel spilling out of the carbs during 1+ G cornering. Think wings and slicks.
...
As it has jammed under its own weight falling in it wouldn’t take much expansion of the carby body for it to free up. With no traces of fuel around I would heat the body with it upside down using ...
I am looking into ordering the ZE41 RZ5 filler rods at the moment from the only supplier world wide. RZ5 is a proprietary product. The advice I have had is the commonly avail mag filler rods are...
What is the extended length of your Fox shocks? Assuming this is for your Ex SPI Chassis? I can check against my Chassis Fox Shocks. Surprised they would need shortening now we run 40mm Clearance in...
https://www.youtube.com/watch?v=dQ2p6BLdS58
F5000 Race Starts at the 2 hour , 32 min mark.
https://m.youtube.com/watch?v=5DqQyc401m8
F5000 Race Starts at the 2 hour , 32 min mark.
https://m.youtube.com/watch?v=5DqQyc401m8
https://www.apexspeed.com/forums/showthread.php?94633-F5000-Race-live-stream-Down-Under
https://www.youtube.com/watch?v=W8ijbQjeCHI
Grid walk and Following Race starts at the 5 Hour , 5 min...
F5000 race Live stream starts in approx. 1.5 hours.
Edit: Grid walk and Following Race starts at the 5 Hour , 5 min mark
https://www.youtube.com/watch?v=W8ijbQjeCHI
...
You are half way there if you have the tool to remove the SKF KM6 bearing nuts. PM me your email and I can send you the Ralt service bulletins for bearing removal/ install if you like.
...
I recalled the thread below a few years back. Lee F mentioned he acquired documentation. Could be a source?
https://www.apexspeed.com/forums/showthread.php?23088-Howard-ignition-info-needed
https://www.apexspeed.com/forums/showthread.php?35118-Lola-T540-33-chassis-and-more
They are quite different. Dcoe are a twin float design and the Ida are a single larger dia float design. I am sure some one will have a use for them.
Brass floats in orig Old school series Dcoe’s. The later 151 and 152 series with the additional air bleed screws run the plastic floats.I have used complete float assy’s swapped between early...
Should be easy to pick up a front wheel drive 4age box and use the bell housing for your template. I have given them away in the past only requiring the engines.
...
Found some 1988 FV / F440 Results sheets which may be of interest
https://www.apexspeed.com/forums/attachment.php?attachmentid=93345&stc=1
https://www.henkel-adhesives.com/vn/en/product/surface-treatments/bonderite_m-cr_magnesiumaero.html
similar to the style used in older Porsche’s but doubt its that easy.
...
https://www.apexspeed.com/forums/attachment.php?attachmentid=91923&stc=1
https://www.apexspeed.com/forums/attachment.php?attachmentid=91904&stc=1
Bound to be a 83 Maurer is this video. https://m.youtube.com/watch?v=MHBzS9Zw26c I have the SA Atlantic championship regs which may give some of the specs you are seeking.
You get a good view of the pinion through the top oil filler plug. Wear on the pinion is basically ten fold of the crown wheel so gives an indication of potential crown wheel condition.
...
Its "Crow Cams" in Oz that can supply you with the req'd Cam.Forget Crane.
Straight from the Cams Bulletin: " Rule B.5. a Camshafts.Where SCCA allows alternate suppliers for camshafts:Crow Cams...
Crow cams supply S2000 approved Camshafts in Oz.
http://docs.cams.com.au/Motorsport/Historic/FORMS/SPORTS%202000%20and%20FF2000%20ADDENDUM.pdf
...