Search:

Bad switch, bad ground, broken wire. Electrical is so fun to chase.

Will

4'x2' table w/ folding legs. Glass cleaner, box/rolls paper towels.ect. Everything in your garage ! I bring a death wheel grinder, sawzall , drill and bits, small mig welder, ( Think spec racers...

Anyone have a phone number for Leon or Jeremy?

Thanks,
Will

Then you use new bolts from Suzuki?

Will

Where can you get aftermarket connecting rod bolts for a gsx r600? Can't find them on the ARP website.

Thanks,
Will

How much [from idle?] rpm is required for a smooth down shift? What range?

Thanks,
Will

Thanks,

Will

The first number is disconnected, the other goes to voicemail. Is he hard to get a hold of [called several times] or just really busy?
and Thanks Jay.

Will

Anyone have a working phone number?

Thanks,

Will

I didn't think so.
Thanks for the offer, don't have an engine to use it on.

Will

Confused about using the up to 2013 engine - rule. If the newer engines are the same 2011 to 2020 can you use a 2015?

Thanks,
Will

Advice on reusing head gasket. Also, connecting rod failure. Broke near the bolt head.

Thanks,
Will

That's a start.

Thanks,

Will

Thanks Cory.
Have to add weight to the car [MC powered] to make 900# and don't have good scales. I know the weight with a 593,
so I will need to add to get to 900#. wondering appox. how much before...

Anyone know the weight of a 593 and the weight of a suzuki 600

will

Anyone have a drawing of this years restrictor [28mm?]

Thanks,
Will

3 or 4 years. I have had the motor running recently. Just figured a good cleaning would help.

Thank You for the link.

Will

Looking for ideas on the best way to clean injectors. [ they have been sitting with fuel in them for quite some time]

Thanks,

Will

George,
Thank you for the reply and part number. Have ordered, should be here Friday.
Was hoping to use the sending unit hole. Looks like its a pipe thread [tapered] .9mm pitch not sure of the...

Where, what port do you get your oil pressure from? GSX R600 Also, anyone know what thread/pitch is the oil pressure sending unit is?Thanks, Will

Very helpful.

Thank You

Will

It's a MC engine with a generator. So a two post switch as suggested would be ok?

will

Which one to use? Switch with or without alternator protection ?

Will

Thoughts on disabling/eliminating
Side stand switch
Tip over sensor
Excva

Thanks,
Will

Thanks Dan and Eric
I have already plumbed the oil cooler as suggested, was not sure of the proper way to seal the stock oil/water cooler, if a "passage" was required. Did not want to do that wrong!...

If I understand correctly, using the ports above the oil pan, right side of engine, use the flat plate with O ring. No "passage" needed.

Thanks, Dan

Will

George,
Thank you for checking. It seems to me that the oil flowing through the cooler goes up to the generator and pistons.
Probably important.

Thanks again ,

Will

So the plate blocks the two ports from the engine?

Will

Thanks George,

I see the o ring on the stock oil cooler, is there no need for a "passage" in the flat plate?

Thanks again,

Will

Oil cooler blanking plate, just a flat plate?

Thanks, Will

Anyone know which sensors are not needed to run the engine?

Thanks,
Will

Many Thanks Russ,

Will

Close to wiring the engine. On the stock wiring harness what is needed and what is not needed to run the engine.
I know sending it to Hyper is one answer, but I had a less than pleasant experience...

what sensors are needed, and which ones are not needed to run the engine.

Will

TDI pilot, Thank you, you have been very helpful, Will

Ready to start fuel plumbing. What size and type of hose is required. Thanks, Will

Thanks, Will

Have all the fittings and hose. Just want to plumb the right line to the top of the heat exchanger.

Thanks,

Will

which is which? Don't have a manual with me.

Thanks,

Will

The ports under the clutch, is one an inlet, one an outlet

Will

Suzuki

Spoke with a engine builder about making the engine "reliable" and it sounded like some internal modifications, more than just changing out rod bolts, are required. I was under the impression any...

Thanks,

Will

Where can I find a drawing of the restrictor plate.

Thanks, Will

Anyone know where one can purchase header flanges ?

Thanks,

Will

Any one know Bill Butterworth ?


Will

Ideas for a Dash. What would be needed at a minimum, to keep the engine safe.
RPM, Shift light, Oil pressure ?
Thanks,

Will

Thanks,

Will

Have been told it is Stainless steel, and Ti. The bike dealers don't know.

Thanks,

Will

Thanks.
Went on a GSX r600 forum and found the bike guys using a Russell Performance
# 640860.
Engine I have, after looking at it actually has one :mad:.

Thanks again,
Will