over east the F1000's race in the Australian Prototype Series. i believe they are clasified under formula libra.
Type: Posts; User: Benno88
over east the F1000's race in the Australian Prototype Series. i believe they are clasified under formula libra.
Most of the cars are from the US. :)
Arise Racing now has 9 Stohrs. my old 2007 v1 Stohr still keeps up and manged to show them the pace that weekend :)
For those of you who are interested, we had our last race meeting here in Australia televised.
here is the link.
https://www.youtube.com/watch?v=cKe9D3CqZzs
hope you guys enjoy some F1000...
Hi guys i currently have a flat shifter pro and i think the solenoid is dying as it is progressively been getting worse with more missed shifts...
Seeing what shifters people recommend/ have for...
Thanks for your input Ghickman. it is just strange because we have had the k line working perfectly for over 2 years with this car, and we also have 9 other cars over here running GSXR k8 motors all...
Hi guys thanks for the replies.
We googled the problem and Aim recommended installing a pull up resistor, to which we installed one, then when checking the wiring we noted that we already had one...
Gday all, just putting out a dew feelers to see if anyone else has any knowledge of this issue, we are currently trying to fault find but just encase someone else has knowledge we dont it might be...
it ended up being 4 small leaks and a lot of blocked parts... will be installing a new radiator this week :) generally an old radiator...
Thanks guys
thanks james, i had a close look at the car yesterday and that looked like a really good spot for air to exit. We are testing tomorrow so something i can play with :)
cheers
Thanks for the input guys.
I like the torch idea as I have flushed the veins out before with a hose and noted a lot of sand coming out (my fault beached the car in the kitty litter after touching...
Hi Glen thanks for the response.
Ok car is wet dumped and it is a fairly sealed section on the exit side of the radiator, I say fairly sealed as we haven't applied foam to the joins on the...
Hi all,
We have a issue with my gen 1 Stohr running a k8gsxr overheating. Currently when racing we are getting 217 deg water temperature.
I'm trying to isolate the issue to being either a...
Thanks for the help guys, it turns out the housing appears to have shrunk a tiny amount which was putting pressure on the bearing. a little clean out and the bearing fit back in perfectly.
Cheers
Thanks for the info guys.
The bearing we very stiff (seized) I have tried to spin it with a drill to get it to loosen up but even after hours of trying and WD40 it has only become loose enough...
Hi all I'm seeking some info about how you remove and replace the internal bearing of the rear A arm for my Stohr. Upon stripping the car we found ours had seized and all efforts to loosen it have...
Im having to use about 11k RPM and slip the clutch almost all the way through 1st gear. if the wheels stop spinning the engine will bog. a tiny amount more clutch is all that is needed to fix that...
Thanks Jake for the info. We just didn't know what was happening and had no idea what else to do being the other side of the world except post on this forum if anyone knew anything.
After reading...
Yeah we are starting to get very concerned the parts wont arrive before the start of the new season though. Plus they have to then make it half way across the world to Australia. Some of the parts...
Thanks Guys Jesse got in contact with me today, sounds like he has be doing heaps for all the new Stohrs. Thanks for you help :) Cheers
Interesting you guys all picked up on the RPM as well. I was in the car infront and having to rev the nuts off it to stay ahead...???
F1000 have now just droped down into the 55s per lap which is...
Hi Glenn
Not a chance of getting out even with my helmet off, i'm not fat in any way and have a 33 inch waist, but still get stuck all the same. the cabin has plenty of room, but the head rest...
Gday guys and thanks for your responses. I really like the idea of the Dzus sliding clip which is similar to the r clip, and having a toggle attached. currently we have the wing-head Dzus and it is...
We have recently purchased a 2008 Stohr f1000 and I am looking for ideas as to how to make the neck collar able to be released quickly. At the moment it is locked by two pins that I would hate to...