GKN tripod joints

So...there seems to be a lack of tripods for late model FC's and FF's. Does anyone know the source of these items? I'm thinking about what street car used them; late 80's or '90s would be the time frame I would think.. Description as below from Primus Parts-



(0)
$64.99
ready to ship
GKN Tripod Joint-30 spline fits Van Diemen 94 thru-current, Citation ,FE, pro MazdaQuick View
GKN TRIPOD JOINT-30 SPLINE FITS VAN DIEMEN 94 THRU-CURRENT, CITATION ,FE, PRO MAZDA

(0)
$64.99
ready to ship
BUY

https://www.primusracingparts.com/as..._thumbnail.jpgQuick View

GKN TRIPOD JOINT-30 SPLINE FITS VAN DIEMEN 94 THRU-CURRENT, CITATION ,FE, PRO MAZDA

As far as I have been able to tell, the GKN GI69 30-spline (but not 22-spline) tripods have been backordered pretty much everywhere since at least March.

When I looked into it in more detail in May, I was told that GKN was quoting a 16-week lead time... but that they had also been quoting a 16-week lead time for months.

I subsequently dug more, and I found one other vendor, YAC of Taiwan, that lists a dimensionally similar part in their catalog, #RE-53-P01. Notably, YAC lists other applications for some of their other tripods, but none were listed for that particular part. Not sure I want to take a flier on it though, or even whether they are actually available rather than being theoretically available.

One word of caution: if you do manage to source some tripods from somewhere, even if they claim to be genuine GKN tripods, check everything very carefully. I got a set of ostensibly "GKN" tripods last winter from a vendor whose reputation has fallen on hard times, and dimension E (as shown below, basically the diameter of the casting) was so different than in the past that the tripods wouldn't fit in my tripod housings. Yes, technically dimension E is unspecified, but it still caused problems for me.

https://www.keacher.com/files/dir11/...dimensions.png

Jeff

Quote:

---

Originally Posted by Teuobk

I subsequently dug more, and I found one other vendor, YAC of Taiwan, that lists a dimensionally similar part in their catalog, #RE-53-P01. Notably, YAC lists other applications for some of their other tripods, but none were listed for that particular part. Not sure I want to take a flier on it though, or even whether they are actually available rather than being theoretically available.

---

Looking at that catalog, ("CR" = Chrysler, "FD" = Ford, etc.), I'm jumping to the conclusion that "RE" might stand for "Renault", and then looking at Renault tripod joints, I found this:

https://shop.febest.eu/tripod-joint-...-2416-meg.html

30 tooth spline... ...29.9mm roller diameter...

It looks like we might have a winner. :)

I sent the company a request yesterday to verify 'in stock'- have heard nothing back yet. If they have them, I'll order a bunch of them, but always leery of a vender I have never heard of, especially one outside the USA.

Quote:

---

Originally Posted by Bob Wright

I sent the company a request yesterday to verify 'in stock'- have heard nothing back yet. If they have them, I'll order a bunch of them, but always leery of a vender I have never heard of, especially one outside the USA.

---

They sell in/to the US via Wally World, with whatever assurances Walmart offers, and at a better price.

https://www.walmart.com/ip/Febest-TR...8895/120638297


Usual disclaimers.

Why do I think that really scares me? :o

So...I ordered a couple of them from Walmart- Surprise! They are out of stock.

Just a tip for those with a bag of crashed tri-pods. They rarely break or wear out. Usually, when we rip off a rear corner, one of the 3 snap rings gets knocked off, a ball moves outward, a few needle bearings fall out, and it gets covered with dirt and grass. For $65, we put a new one on and go.

But they can be cleaned and reassembled, probably 6 crashed ones will make 4 good ones. The snap ring on each ball only holds it together until its in the housing. My guess is 20 mins work will salvage one that came apart. And a reassembled older tri-pod joint may be better quality than a brand new one of unknown or Chinese origin.

Your results may vary, but my cars have won lots of races with reassembled tri-pods. Successful race hire providers, like low-budget club racers, cannot stay financially viable by slapping on new parts every time there is a problem.

Quote:

---

Originally Posted by Bob Wright

...

So...I ordered a couple of them from Walmart- Surprise! They are out of stock.

---

Sure. But it's a great price. :D

same or next day shipping on these, depending on when the order is placed

https://velocityhaus.com/products/vd...n&_ss=e&_v=1.0

I would by them from Greg. All of his stuff is great quality...

Sean

Quote:

---

Originally Posted by alangbaker

Looking at that catalog, ("CR" = Chrysler, "FD" = Ford, etc.), I'm jumping to the conclusion that "RE" might stand for "Renault", and then looking at Renault tripod joints, I found this:

https://shop.febest.eu/tripod-joint-...-2416-meg.html

30 tooth spline... ...29.9mm roller diameter...

It looks like we might have a winner. :)

---

Jeez.... Walmart?!?!?!? https://www.walmart.com/ip/Febest-TR...8895/120638297
https://www.apexspeed.com/forums/att...d=104250&stc=1 https://www.apexspeed.com/forums/att...d=104251&stc=1
This matches the part numbers in the link Alan found. $15.95? YMMV