2006 Van Diemen Zetec

SOLD-FC Zetec-complete racing outfit -$43,000-SOLD

Car / trailer / spares/ set up equipment

2006 Van Diemen #3801Ready to Race, much work done since purchase to sort this car out:
Refit engine gearbox with new hardware ,machine bellhousing true.
New flywheel
New clutch disc
New pressure plate
New clutch slave cylinder seals, shim clearance
New throw out bearing
Set up clutch slave cylinder travel
Reset gearbox shift forks
Set final drive clearance
Straighten / service steering rack
heli coil repair all uprights
Shift linkage repair / set up
Drivers drink system tank with pump
Full steel floor panels (ballast) for 170 lb. driver
-100 db muffler
Set up started to flywheel clearance
Starter heat shield

Includes:
Strong sealed Quicksliver race engine
Three sets OZ racing wheels 6"-8"
Extra Citation style front wing/ shock cover
Body work in good condition, recent paint
Dynamic dampers
Good rain tires
Transport wheels
Quick jack for rear
Low profile hydraulic jack for front
Spare started motor

Wishbone spares:
R&L front lower wishbones
2x front pushrods
1x rear upper wishbone
3x Left rear lower wishbone
Gear ratios:
16-34
15-30 (2x)
16-29
17-28 (3x)
18-28
17-25
18-25
20-27(2x)
21-27
19-24
21-24
24-27
24-26 (4x)
spare dog ring
Gearbox dummy shaft
Braile lightweight battery with charger (total loss system w/o alternator)
Aim EVO 4S with GS dash
Smarty GP Camera
Alignment bars
Camber gauge
Set up / scale platform- New
4 electronic scales- New


2017 Carry on,'16 foot enclosed trailer tandem axle
Electric brakes
Electric winch
Interior lights
Work bench
Tire racks
Compressed air tank
2 spare trailer tires
10x10 awning

Quote:

---

Originally Posted by glenn woloski

FC Zetec-complete racing outfit -$43,000

Car / trailer / spares/ set up equipment

2006 Van Diemen #3801Ready to Race, much work done since purchase to sort this car out:
Refit engine gearbox with new hardware ,machine bellhousing true.
New flywheel
New clutch disc
New pressure plate
New clutch slave cylinder seals, shim clearance
New throw out bearing
Set up clutch slave cylinder travel
Reset gearbox shift forks
Set final drive clearance
Straighten / service steering rack
heli coil repair all uprights
Shift linkage repair / set up
Drivers drink system tank with pump
Full steel floor panels (ballast) for 170 lb. driver
-100 db muffler
Set up started to flywheel clearance
Starter heat shield

Includes:
Strong sealed Quicksliver race engine
Three sets OZ racing wheels 6"-8"
Extra Citation style front wing/ shock cover
Body work in good condition, recent paint
Dynamic dampers
Good rain tires
Transport wheels
Quick jack for rear
Low profile hydraulic jack for front
Spare started motor

Wishbone spares:
R&L front lower wishbones
2x front pushrods
1x rear upper wishbone
3x Left rear lower wishbone
Gear ratios:
16-34
15-30 (2x)
16-29
17-28 (3x)
18-28
17-25
18-25
20-27(2x)
21-27
19-24
21-24
24-27
24-26 (4x)
spare dog ring
Gearbox dummy shaft
Braile lightweight battery with charger (total loss system w/o alternator)
Aim EVO 4S with GS dash
Smarty GP Camera
Alignment bars
Camber gauge
Set up / scale platform- New
4 electronic scales- New


2017 Carry on,'16 foot enclosed trailer tandem axle
Electric brakes
Electric winch
Interior lights
Work bench
Tire racks
Compressed air tank
2 spare trailer tires
10x10 awning

---

What???

Glenn! No!

I didn't think we where that mean to you Glenn! I know of a couple people looking for a Zetec up here so I will send them your way.

Roger

Quote:

---

Originally Posted by RSS

I didn't think we where that mean to you Glenn! I know of a couple people looking for a Zetec up here so I will send them your way.

Roger

---

Thanks Roger! No, had a good time . just don t feel like I have the necessary motivation to keep racing

Quote:

---

Originally Posted by glenn woloski

Thanks Roger! No, had a good time . just don t feel like I have the necessary motivation to keep racing

---

Well I hope we'll see you once at Mission before you pack it in, Glenn.

I've now met two of the people who owned the RF89 after you, and I was looking forward to meeting another.

All the best however it plays out.

Is the price Canadian or US dollars?

Quote:

---

Originally Posted by Goallie11

Is the price Canadian or US dollars?

---

It is USD. He has posted it up here in Canada for $56,500CDN.

-Mark

Quote:

---

Originally Posted by lowside67

It is USD. He has posted it up here in Canada for $56,500CDN.

-Mark

---

if it sells for $56k, I'll bring ours up there tomorrow :-)

didnt know the market was that strong back home

Quote:

---

Originally Posted by Lotus7

if it sells for $56k, I'll bring ours up there tomorrow :-)

didnt know the market was that strong back home

---

At current exchange rates, it's the same amount, CND vs USD

PM Sent Good luck Glenn!

Quote:

---

Originally Posted by Garey Guzman

At current exchange rates, it's the same amount, CND vs USD

---

As a Canadian, I'm quite aware of that :D

Just didnt realize that the Canadian market was that strong these days

Quote:

---

Originally Posted by Lotus7

As a Canadian, I'm quite aware of that :D

Just didnt realize that the Canadian market was that strong these days

---

Only on the west coast!

Quote:

---

Originally Posted by Lotus7

As a Canadian, I'm quite aware of that :D

Just didnt realize that the Canadian market was that strong these days

---

Sorry about that!:D (a boot that? :o)
I was surprised that the two currencies had spread so far apart but there isn't a lot of foreign money conversations in Middle TN!

I'm not in tune with the FC market but for all the stuff included, seems like a decent price. Just about everything needed except the wrenches!

With the recent increase in US dollar strength it's about $40k USD.

Wasn't a bad deal at $43k!

Hi Glenn,
If the car is still available I'll be in BC the week of the 24th and could make some time to visit. Let me know. Thanks Michael.